Posted on Leave a comment

Bedini RPX v3.0 Rife Machine – Presales Open February 17, 2022

Bedini 3.1MHz Sideband Generator v3.0 Prototype "Rife Machine"

It’s very exciting to finally release version 3.0 of the most authentic Rife Frequency generator manufactured anywhere in the world. The link at the end of this sentence titled “Rife Machine” takes you to the Vril.io RPX page that explains why that is true – scroll back up to this link but read this page first: Rife Machine

Below is a sneak peak at the Bedini RPX 3.1MHz Sideband Generator v3.0 – “Rife Machine”. If you’re not familiar with what a sideband generator is, the above link will take you to a page that explains it. Any machine that correctly produces “Rife Frequencies” the way that Rife and his assistant Philip Hoyland did must be done with “sidebands” or it is not a Rife Machine – this is an indisputable, historically-documented fact.

RPX stands for Rife, Priore and an X-Factor but it really should stand for Rife, Priore and Bedini because what his genius incorporated into the RPX is in fact the X-Factor. When we release the v3.0, you’ll learn why the RPX is far superior to any other device even remotely similar and there is only one that is close that I know of and that John Bedini truly was the world’s leading authority on what Rife was doing.

DISREGARD THIS BLOG POST, THE RPX 3.0 IS ALREADY AVAILABLE FOR PURCHASE – GO HERE FOR THE NEW WEBPAGE: RIFE MACHINE

First, here’s a picture of the original unit – it worked perfect but was a bit cumbersome since you have to connect an external signal generator and external battery but this is how John Bedini originally released it late 2014 or early 2015. Below, you’ll see the obvious point to the new RPX 3.0 and why my goal was to make the most user friendly “Rife Machine” ever developed and it has been successfully accomplished.

Bedini RPX 2.0

Below you can see the prototype (no logo or labels for the knobs, switches or jacks). The signal generator inside was designed by Paul Babcock so this couldn’t have happened without his brilliant help. Others were kind enough to offer their services to design one in the past but at that time, the cost was prohibitive, plus, I wanted to stay away from digital as much as possible because digital is fake and analog is of the real world. THE SIGNAL GENERATOR IS 100% ANALOG. Both Rife and Bedini would be thrilled about that!

  1. The LEFT KNOB controls the TIME of the sweep. Specifics will be forthcoming.
  2. The SWITCH between the knobs in the down position leaves it in WIDEBAND MODE so it sweeps from close to 0Hz up to 150kHz to create sidebands that are all even multiples of EVERY SINGLE Rife Frequency automatically without having to. Rife went to 40kHz because that was the upper range of a typical audio signal generator. Why go to 150kHz? It’s one of the things that makes this superior to any sideband generator that creates the Rife Frequencies and I’ll show the math and demonstrations for this so you understand what this means and why it is important. What did Bedini know that Rife and Hoyland possibly didn’t? You’ll find out soon on the page where these units will be available for pre-order on February 17th, 2022.
  3. The RIGHT KNOB controls the narrow band sweep. When the switch is in the up position, it activates the narrow band mode. I’m asked all the time about focusing on certain frequencies. It’s always a bad idea to use any single static frequency as a “wobble” or variation in the frequency was always what was found to be superior. So within the 150kHz range, the narrow band will focus on a 25-30kHz range. If the knob is all the counterclockwise, it will sweep from almost 0Hz up to about 25kHz and as you rotate the dial clockwise, it will keep a 25-30kHz sweep width but higher up in the 150kHz range. There will be a chart printed on top of the case that shows you what frequency range you are at based on the number on the dial, which will be printed on the front panel.

Scroll down to the top of the next picture for an explanation of the rest of the features on the front panel – I just want to break up the text a bit to make it easier to read.

Bedini 3.1MHz Sideband Generator v3.0 Prototype "Rife Machine"
  1. The switch at the top next to the gold RCA jack allows you to use the internal signal generator, which is all anyone will need 99.99% of the time. In the down position, you will be using the internal signal generator and the two knobs and switch to the left. But for those of you who are more technically oriented, you can move the switch in the up position and you can then plug in your own signal generator into that RCA jack. ONLY USE SINE WAVE AND LIMIT THE OUTPUT VOLTAGE OF YOUR SIGNAL GENERATOR TO 2 VOLTS MAX or you can damage the unit. You will able to narrow the sweep to perhaps a few kilocycles on either side of a target frequency to get more specific, extend sweep times beyond what is possible with the internal signal generator or even use frequencies that will produce sidebands that are even multiples of frequencies like 432Hz or any other frequency set of numbers using this method. We’ll teach you how to calculate all that with videos that will be available.
  2. The RED and BLACK banana jacks at the bottom are the output jacks. We supply a cable that you can plug into that and on the other end are alligator clips. You only have to supply your own electrodes. Inexpensive copper tubing from a hardware store than you can get for a few dollars per foot is all you need. Two pieces about 4″ long and maybe 3/8 to 1/2″ diameter is sufficient. Conductive gel is recommended and this one is the only one I could easily find that is free of parabens – this is our Amazon affiliate link: Conductive Gel

    If you’re mechanically inclined, we’d recommend cutting off the alligator clips and soldering the wires to the tubes or adding ring terminals and screwing them to the tubes. Later on, we may recommend a company where you can get some electrodes.
  3. The top right LED light is a RED power light that shows the RPX power is turned on (switch is on the back).
  4. The LED directly under that shows when the PUMPWAVE is on and it will also be RED – just the prototype has the blue light and its just too bright. The switch underneath that can be switched to turn the Pumpwave off and on. This is another one John Bedini’s genius innovations. With the switch off, you can still get the classic Rife Frequencies with the 3.1MHz carrier and sidebands. With the switch on, you get the low frequency carrier (another carrier) that puts the 3.1MHz carrier and sidebands on it and that Pumpwave is a 8-9Hz square wave that takes electrode delivery to another level. Literally, there is nothing that compares to the Bedini 3.1MHz Sideband Generator v3.0.

Above the next picture is a description of what is on the back of the RPX.

Bedini 3.1MHz Sideband Generator v3.0 Prototype "Rife Machine"
  1. The jack and switch below will be flush with the panel on the final units. The jack on the left is for a 16.8 volt 1 amp, regulated lithium-ion charger. The red light on the charger will be on while it is charging and when it is finished charging, the green light will come on. You will not be able to use the RPX while the battery is charging – plugging in the charger will disconnect the battery from the circuit. Please charge the battery fully before using the RPX for the first time. The average use time the RPX is on is about 15 to 30 minutes so you will get a good number of uses before you have to charge the battery again. The switch on the right is the off/on switch to turn on the power. In the down position, it will be off and in the up position, it will be on.
Bedini 3.1MHz Sideband Generator v3.0 Prototype "Rife Machine"
Bedini 3.1MHz Sideband Generator v3.0 - Rife Machine

I’ll make a video walk thru and will put that on the RPX page when pre-orders are open on February 17th along with pricing, etc.

The RPX v2.0 model sold for $425 itself (required you to provide your own battery and signal generator) or $650 for the whole combo kit that included everything except the electrodes. My goal was to make this new RPX 3.0 available for as close to the RPX v2.0 price as possible. The RPX v3.0 will cost more because my production costs are higher. The first 50 (most likely 50) units for pre-sale will be at a super low price compared to what the retail price should be.

Keep in mind that the next closest machine that even comes close to a “Rife Machine” retails for over $1800. That means that since this is a superior technology and it is a super specialty item not available anywhere else that the RPX v3.0 should have a retail price of around $2000 to $2500 (but it won’t be) and it would be worth ever penny comparing value vs value in terms of sale price.

Make sure to order as soon as the pre-order page opens up on February 17th because you’ll be pleasantly surprised with our pricing! You’ll also be earning points on emediapress.com that is good for credit toward digital downloads. More to come…

Remember to go to this page to learn more in depth about the truth about what a Rife Rife machine is and what it isn’t’: Rife Machine

Posted on Leave a comment

Low Cost Rife Microscope?

Royal Raymond Rife is well known for his “Rife Machine” that uses the “Rife Frequencies”, which he discovered by using his Rife Microscope.

What is of significance about this microscope is that it is able to see things that are so small that it’s considered impossible according to the science of conventional optics. Rife actually succeeded in doing this by using some very innovative  prismatic and other methods. This is what his miracle microscope looked like:

Rife Microscope
Rife Microscope

Having this kind of technology opens up a whole new world of possibilities in many different areas of science.

Although the Rife Microscope is long gone, there is a new, relatively simple and in expensive method that has been devised that apparently will give all the same benefits!

Conventional microscopes can only see things that are larger than the half wavelength of the light that is being used, which limits the objects being seen to about 200nm (nano-meters) or larger.

Although there have been breakthroughs in microscope technology for a while now, it wasn’t until recently that this became possible using  visible light. That means you would be able to see into the world that has remained invisible since the days of the Rife Microscope.

By using millions of 15nm wide titanium dioxide spheres that is applied to the object you want to examine, you’ll be able to see object as small as 45nm.

Keep in mind that this is with full visibility of the objects in life time as if you are looking at a live specimen under a regular microscope. And, if you use this in conjunction with any normal microscope, just by applying this new lens, it will increase its optical magnification power by five times.

For the full text of the published paper on this breakthrough technology, go here: http://advances.sciencemag.org/content/2/8/e1600901.full

For the real story on what the real Rife Machine was and how it as used, check out this new important historical disclosure: Bedini-RPX, The Bedini-Rife-Priore Device History & Schematics.