In 2019 when Eric Dollard presented on the 20:1 scale model replica of the Colorado Springs Magnifying Transmitter, Dr. Adrian Marsh was there to help analyze the MWO, the Colorado Springs transformer and more. He was able to quickly figure out how to get the MWO pulse modulator to power the Colorado Springs transformer and several experiments were conducted on the fly.
This year, Dr. Marsh gave a comprehensive overview of using a Vector Network Analyzer to show more information about the resonant peaks, serial vs parallel mode and more. It is must easier to obtain this information with a VNA compared to using a current transformer and analog volt meter. It’s recommended that you do understand the old-school analog method because it is important to understand that but for ultra fine tuning, the VNA is the way to go.
You’ll see a lot of charts produced by the VNA output and Dr. Marsh shares the comparison between a very affordable VNA compared to his HP one that was a $100k unit when brand new. The results are extremely close.
In addition to the VNA presentation, you’ll also see a replication of Eric Dollard’s gold-ratio high voltage discharges! This is the first time this has been replicated by anyone other than Eric to our knowledge. This was done with equipment that Dr. Marsh brought over from the UK in a suitcase.
It’s very exciting to finally release version 3.0 of the most authentic Rife Frequency generator manufactured anywhere in the world. The link at the end of this sentence titled “Rife Machine” takes you to the Vril.io RPX page that explains why that is true – scroll back up to this link but read this page first: Rife Machine
Below is a sneak peak at the Bedini RPX 3.1MHz Sideband Generator v3.0 – “Rife Machine”. If you’re not familiar with what a sideband generator is, the above link will take you to a page that explains it. Any machine that correctly produces “Rife Frequencies” the way that Rife and his assistant Philip Hoyland did must be done with “sidebands” or it is not a Rife Machine – this is an indisputable, historically-documented fact.
RPX stands for Rife, Priore and an X-Factor but it really should stand for Rife, Priore and Bedini because what his genius incorporated into the RPX is in fact the X-Factor. When we release the v3.0, you’ll learn why the RPX is far superior to any other device even remotely similar and there is only one that is close that I know of and that John Bedini truly was the world’s leading authority on what Rife was doing.
DISREGARD THIS BLOG POST, THE RPX 3.0 IS ALREADY AVAILABLE FOR PURCHASE – GO HERE FOR THE NEW WEBPAGE: RIFE MACHINE
First, here’s a picture of the original unit – it worked perfect but was a bit cumbersome since you have to connect an external signal generator and external battery but this is how John Bedini originally released it late 2014 or early 2015. Below, you’ll see the obvious point to the new RPX 3.0 and why my goal was to make the most user friendly “Rife Machine” ever developed and it has been successfully accomplished.
Below you can see the prototype (no logo or labels for the knobs, switches or jacks). The signal generator inside was designed by Paul Babcock so this couldn’t have happened without his brilliant help. Others were kind enough to offer their services to design one in the past but at that time, the cost was prohibitive, plus, I wanted to stay away from digital as much as possible because digital is fake and analog is of the real world. THE SIGNAL GENERATOR IS 100% ANALOG. Both Rife and Bedini would be thrilled about that!
The LEFT KNOB controls the TIME of the sweep. Specifics will be forthcoming.
The SWITCH between the knobs in the down position leaves it in WIDEBAND MODE so it sweeps from close to 0Hz up to 150kHz to create sidebands that are all even multiples of EVERY SINGLE Rife Frequency automatically without having to. Rife went to 40kHz because that was the upper range of a typical audio signal generator. Why go to 150kHz? It’s one of the things that makes this superior to any sideband generator that creates the Rife Frequencies and I’ll show the math and demonstrations for this so you understand what this means and why it is important. What did Bedini know that Rife and Hoyland possibly didn’t? You’ll find out soon on the page where these units will be available for pre-order on February 17th, 2022.
The RIGHT KNOB controls the narrow band sweep. When the switch is in the up position, it activates the narrow band mode. I’m asked all the time about focusing on certain frequencies. It’s always a bad idea to use any single static frequency as a “wobble” or variation in the frequency was always what was found to be superior. So within the 150kHz range, the narrow band will focus on a 25-30kHz range. If the knob is all the counterclockwise, it will sweep from almost 0Hz up to about 25kHz and as you rotate the dial clockwise, it will keep a 25-30kHz sweep width but higher up in the 150kHz range. There will be a chart printed on top of the case that shows you what frequency range you are at based on the number on the dial, which will be printed on the front panel.
Scroll down to the top of the next picture for an explanation of the rest of the features on the front panel – I just want to break up the text a bit to make it easier to read.
The switch at the top next to the gold RCA jack allows you to use the internal signal generator, which is all anyone will need 99.99% of the time. In the down position, you will be using the internal signal generator and the two knobs and switch to the left. But for those of you who are more technically oriented, you can move the switch in the up position and you can then plug in your own signal generator into that RCA jack. ONLY USE SINE WAVE AND LIMIT THE OUTPUT VOLTAGE OF YOUR SIGNAL GENERATOR TO 2 VOLTS MAX or you can damage the unit. You will able to narrow the sweep to perhaps a few kilocycles on either side of a target frequency to get more specific, extend sweep times beyond what is possible with the internal signal generator or even use frequencies that will produce sidebands that are even multiples of frequencies like 432Hz or any other frequency set of numbers using this method. We’ll teach you how to calculate all that with videos that will be available.
The RED and BLACK banana jacks at the bottom are the output jacks. We supply a cable that you can plug into that and on the other end are alligator clips. You only have to supply your own electrodes. Inexpensive copper tubing from a hardware store than you can get for a few dollars per foot is all you need. Two pieces about 4″ long and maybe 3/8 to 1/2″ diameter is sufficient. Conductive gel is recommended and this one is the only one I could easily find that is free of parabens – this is our Amazon affiliate link: Conductive Gel
If you’re mechanically inclined, we’d recommend cutting off the alligator clips and soldering the wires to the tubes or adding ring terminals and screwing them to the tubes. Later on, we may recommend a company where you can get some electrodes.
The top right LED light is a RED power light that shows the RPX power is turned on (switch is on the back).
The LED directly under that shows when the PUMPWAVE is on and it will also be RED – just the prototype has the blue light and its just too bright. The switch underneath that can be switched to turn the Pumpwave off and on. This is another one John Bedini’s genius innovations. With the switch off, you can still get the classic Rife Frequencies with the 3.1MHz carrier and sidebands. With the switch on, you get the low frequency carrier (another carrier) that puts the 3.1MHz carrier and sidebands on it and that Pumpwave is a 8-9Hz square wave that takes electrode delivery to another level. Literally, there is nothing that compares to the Bedini 3.1MHz Sideband Generator v3.0.
Above the next picture is a description of what is on the back of the RPX.
The jack and switch below will be flush with the panel on the final units. The jack on the left is for a 16.8 volt 1 amp, regulated lithium-ion charger. The red light on the charger will be on while it is charging and when it is finished charging, the green light will come on. You will not be able to use the RPX while the battery is charging – plugging in the charger will disconnect the battery from the circuit. Please charge the battery fully before using the RPX for the first time. The average use time the RPX is on is about 15 to 30 minutes so you will get a good number of uses before you have to charge the battery again. The switch on the right is the off/on switch to turn on the power. In the down position, it will be off and in the up position, it will be on.
I’ll make a video walk thru and will put that on the RPX page when pre-orders are open on February 17th along with pricing, etc.
The RPX v2.0 model sold for $425 itself (required you to provide your own battery and signal generator) or $650 for the whole combo kit that included everything except the electrodes. My goal was to make this new RPX 3.0 available for as close to the RPX v2.0 price as possible. The RPX v3.0 will cost more because my production costs are higher. The first 50 (most likely 50) units for pre-sale will be at a super low price compared to what the retail price should be.
Keep in mind that the next closest machine that even comes close to a “Rife Machine” retails for over $1800. That means that since this is a superior technology and it is a super specialty item not available anywhere else that the RPX v3.0 should have a retail price of around $2000 to $2500 (but it won’t be) and it would be worth ever penny comparing value vs value in terms of sale price.
Make sure to order as soon as the pre-order page opens up on February 17th because you’ll be pleasantly surprised with our pricing! You’ll also be earning points on emediapress.com that is good for credit toward digital downloads. More to come…
Remember to go to this page to learn more in depth about the truth about what a Rife Rife machine is and what it isn’t’: Rife Machine
Here’s a short video showcasing some of the vendors (not all of them were available to share what they’re offering) at the 2021 ESTC.
Please support the vendors because they help to make the conference possible. Emediapress.com is an affiliate of for a couple of the products available.
This is the first ever air conditioner given the “Most Efficient” award by Energy Star – Energy Star finally got something right. This AC is about 35% more efficient than normal ACs due to the inverter technology, but look at the design!
The window literally closes right down the middle of the unit keeping the noisy compressor side on the other side of the window while only the quiet, cool air is on the inside. Its only a few dB louder than a library.
I just ordered one and am having it delivered to Home Depot since for some reason, through Amazon, it can’t be delivered go my home due to the location – never seen that before. In any case, this Midea company offers an 8000, 10000 and 12000 BTU unit.
Needless to say, you can still have full functionality of your window when you want unlike other AC’s where the are locked in the up position due to the fact that you simply have to have the window all the way open for the AC to stick through the opening but not with this one.
I have a portable AC that I stick in the window and use for maybe 2 months here in Spokane, Washington but it’s not cutting it now and that is why I was prompted to search for a better AC and was happy to have found this Midea U-Shaped Air Conditioner.
Check out the temperature here in the Inland Northwest – going to be 113F tomorrow and 100 minimum every day for the next week and unfortunately, that’s not Photoshopped!
If you could have a cloth to wrap your mobile phone in so you are not subject to its radiation would you want it? There are countless applications for this kind of material and it’s getting more and more popular by the day.
Tonight, I tested some shielding cloth, which many promote as “EMP Cloth” and verified that what it actually does is block radio frequencies. I wrapped my mobile phone in some and folded it over enough so that there are no openings that would allow any RF to sneak into any of it and from another phone I called it but it just went to voicemail.
When I removed my phone from the cloth, instead of a wifi or 4G or LTE symbol, it had a circle with a line through it meaning that while it was wrapped in the cloth, it could not find a connection! Obviously, we can put the phone in a metal box with a metal lid, but we don’t always want to carry something like that around, so if we can just take some cloth and wrap it up, then our bodies are free of any of its emissions because the RF can’t get out or in!
There are a lot of other uses that will be evident and the cost of this kind of material is actually affordable.
What about something that may partially block you from the deadly effects of 5G emissions? We’re living in a soup of RF and depending on certain frequencies, it is NOT hospitable to life and can cause a lot of other problems.
I don’t necessarily agree with the vocabulary and definitions of what their website says, but I can say that it does block the RF from going through. It is extremely rare that I ever promote external products but when I tried this shielding cloth myself, I know it works. It’s also available through Clickbank just like the digital books and videos published by A & P Electronic Media so the merchant is trustworthy.
Please take a moment and let us know what new products you want to see available first – ballpark estimated pricing is listed in the descriptions. We have quite a few production ready prototypes ready to be manufactured so please be as accurate as possible when ranking each according to the 10 star options.
1 star = no interest, you don’t want one 10 stars = very high interest, you want one right away
If you could have a cloth to wrap your mobile phone in so you are not subject to its radiation would you want it? There are countless applications for this kind of material and it’s getting more and more popular by the day.
